Industrial Door TOORS Indy

Optimum solution

The industrial sectional door TOORS Indy is the state-of-the-art product designed to meet the requirements and expectations of each individual.

Individual solution without compromise

Every industrial door TOORS INDY is tailored according to the building character and customer’s requirements.

Minimum space requirements

The sectional door opens vertically. The door construction provides maximum available space both in front and behind the door. Depending on the building characteristics, the door either rolls under the ceiling, remains placed vertically by the wall or copies the roof slope. The whole system is mounted behind the building opening and enables full use of the available opening width and height. Such a practical solution also reduces a potential risk of the system damage. Convenient controls for easy operation.

Safety complying with the European standard EN 13241-1.

TOORS Indy industrial door is safe

Our doors are extremely safe. The TOORS INDY sectional door is tested and certified in compliance with EN 13241-1

• Finger anti-trap protectionprevents trapping and contusion of fingers between the door sections (model Protect)
• The side guides are covered and make it impossible to insert a hand or any other object between the lift profiles and the door section.
• The spring failure safeguard will prevent the door section from falling due to a   spring failure
• The cable failure safeguard will prevent the door section from falling due to cable loosening or breaking

Panels – Choose out of Two Models

The industrial door TOORS INDY is available in two models.

1.Standard 

2.Protect with Hoesch Sectiotec panels

The panels are designed as sandwich panels
(thin sheet, insulation foam, thin sheet) and are
40 mm thick as minimum in order to provide
optimum insulation properties. Dangerous gaps,
occurring during opening/closing stages, can be
at some panel types covered by means of special
shaping of the panel nose    

Standard                                          

• Excellent heat insulation properties
• Sandwich panel, 40 mm thick
• Traditionally shaped panel “nose”
• Highly corrosion-resistant
• Strong core made of hard HCFC-free polyurethane foam
• High stability, robustness                                            

Panels are characterized by high stability and robustness. The panels provide excellent heat insulation properties secured by a polyurethane foam layer. The panels are designed as sandwich panels and are 40 mm thick. Both sides of the Standard panels are covered with the Stucco surface, resembling the orange peel. The panels are available in six various colour alternatives; the inner surface of the panel is coated with RAL 9010 paint, i. e. very light grey. The panels can be optionally coated with the paint Plus, specially designed for industrial doors. The Plus paint is three times harder and provides even more effective protection against damage. 

Stucco Pattern

Stucco is the traditional pattern which never
loses vogue and looks attractive even after
many years of service.                                       

Variety of Panel Colour Shades

The panels may be coated to various colour shades to choice. The RAL 9010 or 9002 range hues are available; nevertheless, any hue of the RAL or NEC samplers can be ordered. The door coating can be either single- or double-sided.

Variety of Panel Colour Shades

Protect

Hoesch Sectiotec panels

Excellent heat insulation properties

• Sandwich panel, 40 mm thick
• Strong core made of hard HCFC- free  polyurethane  foam
• Finger anti-trap protection (for more details, see page 7)
• Highly corrosion resistant due to GALFAN® surface treatment
• Maximum stabile and robust structure

Protect panels - basic

•       External side: Lamella Stucco RAL to choice
•       Internal side: Lamella Plain RAL 9002

or 

•       External side: Lamella Plain RAL 9010
•       Internal side: Lamella Plain RAL 9010

Basic Colours

Doors Protect  - V-profile

• 1.       External side:  V-profile Plain RAL 9006
• 2.       Internal side: Lamella Plain RAL 9002

Doors Protect – groove-free

Hoesch panels options

Do you need more light or fresh air in your halls?

 Select the optimum solution from our products

All-Aluminium Sections

The sections are assembled from anodized aluminium profiles, equipped with the finger anti-trap protection. The frame can be filled with variety of materials depending on the required level of heat insulation, light transmission and general appearance

Windows

Double insulation glazing SAN UV – excellent optical properties, high weather-resistant (UV radiation), minimum risk of dust or moisture penetration.

Preliminary Construction Activities

Each lift type requires the particular construction adaptations, ensuring the optimum operation of the whole system.

Lift Types of Industrial Door TOORS Indy

Standard lift

The standard lift is the prevalent rail system of the industrial door. The standard lift is installed in case the free space above the opening edge is between 420 mm and 1000 mm. Torsion springs are placed above the vertical part of rails. The horizontal part of rails can also be bevelled.

High Lift

When the free space above the opening edge is larger than 1000 mm, the high lift is a better solution compared to the standard lift (however, it can be also applied for lower lintels). The system ensures the optimum utilisation of the space above the opening, as the door rails rise strictly vertically and they arch just close to the ceiling. The high lift therefore provides more space compared to the standard lift installed in the identical opening.

Besides the width and height, the HL is also the significant indicator; it defines the distance between the lower edge of the rail horizontal part and upper edge of the opening. At the high lift, the springs are always installed above the vertical part of the rails; nevertheless, they can also be placed on the sleeve above the door opening. Such a solution provides easy installation and minimum requirements for preliminary construction adaptations and service. The horizontal part of rails can also be bevelled.

Vertical Lift

When the free space above lintel is equal to or larger than the opening height + 400 mm, the door without the horizontal part of rails can be installed. Such doors are fitted with the vertical parts of rails only. Torsion springs are placed above the rails; however, they can also be mounted to the sleeve above the lintel. The vertical lift solution shows the same advantages as the high lift system.

Low Lift

The low lift is a special door track system enabling installation of the door from the minimum lintel height of 200 mm. At such a low lintel, the torsion springs must be mounted in the back, behind the horizontal rails. To install the torsion springs in front of the lintel, the minimum distance of 330 mm from the lintel edge to the ceiling is required. The characteristic feature of the low lift system is a horizontal track composed of two rails securing more effective sealing of the door (upper section).  

Explanatory notes to lift types

•   SL - standard lift
•   FSL – bevelled standard lift (following the roof slope)
•   HL – high lift
•   FHL – bevelled high lift (following the roof slope)
•   HL-T / HL-L – high lift (with torsion springs above the lintel)
•   VL – vertical lift
•   VL-T / VL-L – vertical lift (with torsion springs above the lintel)
•   LL-CE – low lift (with torsion springs in the back)  

The automated sectional door, fitted with an electric drive and other accessories, enables safe and easy operation.

Shaft Drives GfA-ELEKTROMATEN

•  High reliability and long lifespan

100 % quality control in each production stage. Every motor is tested on capacity and function prior to distribution.

•  System solution for right functionality

All drives, control units and accessories are fully compatible and mutually tested.

•  Wide range of drives and alternatives for the optimum solution

We are ready to tailor the optimum solution to suit your needs and requirements by means of the ideal combination of the drive capacity, type of emergency control, supply voltage, control unit and accessories.

•  Emergency manual control

In case of a power failure, two types of the emergency control are available:

1.       Rapid chain

2.       Release

 Motor Types

The sectional door motors are intended for direct
installation to the shaft. In terms of the door/motor
emergency control (in case of a power failure, for instance),
the drives can be split into two following categories:

1. KE MOTORS  controlled by the integrated endless chain.     

2. E MOTORS declutchable motors. In case an emergency occurs, the door shaft will detach  from the motor and the door can be controlled manually. The door equipped with the E-motor must be also fitted with the spring failure safeguard

GfA (Gesellschaft für Antriebstechnik)

The company has been producing control units and drives for industrial doors in the production plant placed in Düsseldorf, Germany, since 1954. At present, GfA supplies the market with more than 100,000 drives a year under The ELEKTROMATEN® brand.

All GfA products are manufactured to the highest standard of precision and tested with the sophisticated measuring devices. Each process involved, whether it be distribution, design or production, is certified to comply with DIN EN ISO 9001:2000 standards. This is why GfA is able to guarantee high quality of the products. Today the name GfA stands for the highest safety standards in drive technology, plug-in control units and advanced, high quality production.

All GfA products are manufactured to a precision and with emphasis on quality. The results of the precise production are verified by means of the sophisticated instruments: every process, whether manufacture, assembly, control, or logistics, is subject to the quality standard DIN EN ISO 9001.

Download the list of GfA control units and available extensions in pdf.

Control Units

TS 956 and TS958  TOTMAN
(„dead man control“)

•  IP65 for direct connection or IP54 with a CEE plug
•  Integrated command buttons OPEN-STOP-CLOSE
•   7-segment status and info display unit
•  Emergency stop (optional)
•  Key switch (optional)
•  Cycle counter
•   Service cycle counter
•   Power control in OPEN direction

TS 961 and TS970 Pulse Control

Additional components compared to TS 956 and TS 958:

•  Rotary switch for intermediate position / partial 
   opening (optional)
•  Automated time-controlled closing (1 – 240 s)
•  Automated floor adjustment (TS 970)                   

 TS 981

Additional components compared to TS 970:

•   One-way and both-way operation control
•   “Air lock" function (separate module)
•   State signalling function (separate module)
•   RWA control (connection to the fire detector with the door emergency opening)

Motor Accessories – Easy Control

The standard motor functions and controls may be extended with additional accessories. Examples of the most common accessories are mentioned below.

Optical Safety Edge

• The optical safety edge is mounted inside the lower sealing profile and ensures stopping of the door when in contact with an obstacle and its consequent release. IP68.

 Light Barrier

• The light barrier prevents the contact of the obstacle and door.

Reflex Light Barrier

• IP65, radius 8 m 

Unidirectional Light Barrier

• IP65, radius 25 m

Remote Control

• Receiver with a USB connector for connection to the control unit
• One- or four-channel transmitter

Connection Box with a Spiral Cable

• Transmits the data from the door to the drive control unit, IP65. 

External Lockable Command Button

• IP65

Traffic Lights

• Bulb E27, 230 V, 40 W, IP65